Lst 0130 Bedienungsanleitung

Fire Detection Control PanelSeries BC216User Manual Part ADescriptionOperating Instructions Subject to change without notice© by MEP - Gefahrenmeldete

out the reconditioning. Together with the fire prevention officer you have to determine the additionalprotective measures that are to be taken until t

Further approvals are in preparation.1.4 WarrantyYour fire detection control panel Series BC216 has been manufactured with greatest precision andcare.

Delay timeThe delay time consists of reaction- and exploration time. During the reaction period the activationof the transmitting devices for fire ala

LoopRing-shaped wiring with bi-directional data-bus to connect intelligent fire detectors (e.g., sensors,detectors) and actuation devices to the fire

ing proper equipment for transmission (e.g., continually monitored telephone cables). The transmit-ting device for fire alarm messages which can also

2 Fire detection control panel Series BC216The construction of a typical fire detection system, the most important features of the fire detectioncontr

2.2 Typical construction of a fire detection system with network control panelBCnet216Basically the network fire detection control panel BCnet216 does

Basically all fire detectors and other devices that may be connected to a stand-alone control panel oftype BC216-1 may also be connected to every sing

In case of an alarm, the user can explore the possible danger prior to the transmission of the fire alarmto the fire brigade by using the alarm delay

for false fire alarms. The fire detection control panel BC216-1, besides automatic adjusting of the sen-sitivity of the detectors, is capable of displ

HB216AE.SAM / 0130 / AN9161202ZN5002/73/22User Manual Series BC216 / Part AAll rights reserved. Under the copyright laws, no part of this manual or o

played on the control panel. In addition to the zone number, the fire detection control panels SeriesBC216 are capable of displaying a zone-specific t

2.4.4 ActuationsPractically any number of actuations can be activated by the fire detection control panels SeriesBC216. The activation of each actuati

3 Displaying and operating elementsThe functions and effects of the displaying and operating elements of the fire detection control panelSeries BC216

You operate the fire detection control panel Series BC216 with the clear and sturdy keypad on the frontof the case. An illuminated LC-display and ligh

The third line displays the text information for the element of the current alarm. Is no element textprogrammed, the second text information for the z

3.6 Reset-buttons'Panel reset'-button: All actual fire alarms, technical messages, fault alarms, faults and actuations arereset in one actio

The displaying and operating elements of the field TRANSM. DEVICE 1 are reserved for the primarytransmitting device, which is exclusively designed for

this is only possible by the use of the menu (see from page 43 in Chapter 4.7.10: "Displaying andoperating alarming devices - menu point [Alarmin

330 21.12.2002 08:45 ENABLEMENT 0002 1.Floor Storage area331 21.12.2002 08:47 AUTHORIZATION EXIT User levelFigure 6: Example of a protocol print-outTh

4 Basic operation of the fire detection control panels Series BC216The basic functions of the fire detection control panels Series BC216, together wit

Contents1 Introduction...71.1 Symbols and type fonts ...

By confirming the menu point [Exit authorization?], authorization level 2 is left. Has no operationoccurred for 15 minutes, the control panel returns

During activities that require authorization level 4, the fire detection control panel is usuallycompletely out of service!4.2 Operations using single

With the possibility to reactivate the primary alarming device, you can repeat a prematurely inter-rupted evacuation alarm of a building without activ

By exception of the primary transmitting device, all other transmitting devices are operated exclusivelyby the use of the menu. Only the primary trans

the beginning of a code and leads you straight to the menu point [Authorization code:]. This hap-pens also if you are in a display-menu point such as,

Authorization level 1 Authorization levels 2 and 3Main menu points Submenu points Main menu points Submenu pointsAlarms AlarmsActivated actuations Act

4.5 Entering and exiting authorization level 2To enter authorization level 2 from authorization level 1, you have to enter the 4-digit user code pro-g

The number of incorrect inputs is limited. After 5 incorrect inputs, the input of the installer-code islocked for 15 minutes.To return from authorizat

4.7.2 Displaying activated actuations - menu point [Activated actuations]Scroll through all activated actuations by using the '↑↓'-buttons (

1.TECH.DIS 0003<zone text1><zone text2> Figure 11: Example for the display of the disablement of a technical message, zone 3.In this cas

4.7.1 Displaying fire alarms - menu point [Alarms] ... 374.7.2 Displaying activated actuations - menu point [Acti

No alarm is transmitted by detector zones that are disabled, faulted or put in test condition. A detectorzone that is disabled, faulted or put in test

If the function "measured value/maintenance" is selected, the LC-display shows the measured value atthe time of function selection of this d

The activation of an actuation for test purposes acts like a real activation! Consider that thismay lead to an unintended activation of an extinguishi

If the parameters of the transmitting device have been set to take the device out of operation automati-cally in authorization level 2 or 3 (see from

The event memory can be accessed by using the menu point [Event memory]. You can set one of thepossible filters [Display all], [Control panel] or [Det

4.7.12.4 Correcting the clock time - submenu point [Clock time correction]The built-in quartz clock has an accuracy of a few seconds per year. In case

4.7.12.9 Displaying the installed componentries - submenu point [Componentries]You can display the corresponding number of the software version and an

With a single measured value print-out, the output of current events is suppressed until the print-outhas been finished. With the periodical measured

4.8 Operating the control panel by using the fire brigade control unitA fire brigade control unit offers the fire brigade the possibility to operate t

5 Operating conditions of fire detection control panels Series BC216This chapter describes the operating conditions of a fire detection control panel

6.1.1 Testing of the fire detection control panel and the power supply devices ... 656.1.2 Testing of detectors ...

By using the '↑↓'-buttons, you can browse in an event-category (e.g., in all current alarms); by usingthe '← →'-buttons, you can s

No rules or instructions beyond those necessary for the operation of the control panel are given in thisUser Manual. You have to analyze the site-spec

The activation of a transmitting device and of an alarming device are classified as an actuation andtherefore activate the red light-emitting diode &a

The information on the transmission to the fire brigade and the sirens given in this chapter are onlyvalid for the common case that the panel was conf

Starting at the display of alarms you can scroll to the main menu points [Faults] and [Disablements] byusing the '← →'-buttons. In these men

5.2.5 Fire alarm condition - special case: alarm in an interdependence of two detectorsInterdependencies of two detectors can be set during planning f

line will show the second zone text, if this is available. The fourth line is reserved for fire alarmmessages.If the parameters have been set accordin

The internal buzzer is sounding constantly.You can silence the internal buzzer by using the button 'Silence buzzer'. The buzzer is activated

display of the panel, the yellow light-emitting diode 'Technical message' and the buzzer are activatedby these messages also.Technical messa

At a fault in the primary transmitting device or the primary alarming device, the corresponding yel-low LED-displays are flashing.At a fault in the po

HB216AE.SAM / 0130 / AN9161202ZN5002/73/66User Manual Series BC216 / Part A

ConditionEffectDisplaying (1st line)Fault in an element (e.g., Nr. 5) of a detector zone (e.g., Nr. 3) for technicalmessagesThe transmitting of an ala

The fire detection system is supplied with power by the stand-by battery in case of a fault with mainspower shut down. The required bridging time is r

At disablement of the primary transmitting device or the primary alarming device, the correspond-ing yellow disablement-LED-displays are illuminated.T

In case of several current disablements, you can tell the order of their occurrence by the number infront of the disablement message. Starting with th

Additional information (e.g., date and time of the test procedure, the number of current test procedures,hints for operating the menu, hints for autho

6 Ensuring the efficacy of the system by the userIn order to ensure the efficacy of the fire detection system the user periodically should make sure t

After finishing the testing of the detectors you have to terminate the test condition immediately.Detection zones in test condition cannot transmit an

6.3 Reconditioning and maintenanceParts of the system that have a fault are not able to perform their functions efficiently or at all. There-fore have

7 Event memory - entriesYou can browse in the event memory by the use of the '↑↓'-buttons. The first three lines of the LC-display show the

Event Event text Text 2nd line Text 3rd line Additional text(info-button)Test condition offFLT.TEST.T 0001/001zone text 1 zo. text 2 / element textTe

1 IntroductionDecades of research and development of LST in the field of fire detection control panel technology andthe successful cooperation with re

Event Event text Text 2nd line Text 3rd line Additional text(info-button)Test activation terminationAL-DEV.TEST.T 01alarming device text 1 alarming

Event Event text Text 2nd line Text 3rd line Additional text(info-button)Fault termination functionmodule 2FAULT.T FM2fault causeFault termination INF

8 IndexActivation condition of actua-tions, 55Actuation, 21- Display, 38, 41- Light-emitting diode, 25- Operate, 41- Two-zone dependency, 56Alarm coun

Software version, 8, 46Specifications, 67Stand-by battery, 18, 65- Disposal, 65Standards, 10System fault, 10, 25Technical message, 49, 56- Display, 38

This User Manual is not designed as a description of or as an operating instruction for a fire detectionsystem. Therefore, detailed instructions for h

in the expansion of the area surveilled require careful replanning and adaptation of the fire detectionsystem.The fire detection system has to be chec